Custom Rib Cuff — Spandex Blend with Injection Moulding
We supply rib cuff to garment factories and brands, built in Spandex Blend with injection moulding for outerwear and jacket programmes. On a trim like this the specification that decides the outcome is recovery after stretch, because a cuff that bags stays bagged, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 3000 pieces per style per finish.
The failures here are predictable: minimum order quantities far above what a growing brand can absorb, or shade variation within one carton. We lock material, finish, dimension and tolerance before bulk, and prepare GSO conformity with Arabic labelling so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Rib Cuff |
|---|---|
| Width | 6 cm |
| Construction | 1x1 rib |
| Base material | Spandex Blend |
| Finish / process | Injection Moulding |
| Colour options | 12 Pantone-matched shades |
| Packing | packed to your size ratio |
| MOQ | 3000 pieces per style per finish |
| Sampling | 12 working days, 5 days per revision |
| Bulk lead time | 15-50 days after approval |
| Compliance | GSO conformity with Arabic labelling; EN 71 part 3 for decorative components |
| Ship to | Jebel Ali (the Middle East) |
What buyers can customise
- Die-Casting — available on Spandex Blend, quoted per position and per colour.
- Stamping — available on Spandex Blend, quoted per position and per colour.
- Sewn Edge — available on Spandex Blend, quoted per position and per colour.
- Ultrasonic Welding — available on Spandex Blend, quoted per position and per colour.
- Crochet — available on Spandex Blend, quoted per position and per colour.
- Braided Weave — available on Spandex Blend, quoted per position and per colour.
- Embroidery — available on Spandex Blend, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed width
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with injection moulding applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Jebel Ali with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same recovery after stretch.
FAQ
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
How long does sampling take?
A first sample takes 12 working days, and each revision about 5 days.
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
Which compliance documents do you provide?
We prepare EN 71 part 3 for decorative components and the supporting test reports for the destination market.
Start your rib cuff programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
