Custom Tag Pin — Polyethylene (PE) with Hot Foil Stamping
We supply tag pin to garment factories and brands, built in Polyethylene (PE) with hot foil stamping for denim and workwear programmes. On a trim like this the specification that decides the outcome is head strength, because a snapped head leaves the pin in the garment, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 2000 pieces per style per finish.
The failures here are predictable: a finish that tarnishes or rubs off after washing, or colour drift between the approved sample and the bulk trim. We lock material, finish, dimension and tolerance before bulk, and prepare REACH and GPSR documentation so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Tag Pin |
|---|---|
| Length | 75 mm |
| Type | loop lock pin |
| Base material | Polyethylene (PE) |
| Finish / process | Hot Foil Stamping |
| Colour options | 16 Pantone-matched shades |
| Packing | polybag per 100 |
| MOQ | 2000 pieces per style per finish |
| Sampling | 7 working days, 3 days per revision |
| Bulk lead time | 15-50 days after approval |
| Compliance | REACH and GPSR documentation; OEKO-TEX Standard 100 for dyes and trims |
| Ship to | Rotterdam or Felixstowe (Europe) |
What buyers can customise
- Overlocked Edge — available on Polyethylene (PE), quoted per position and per colour.
- Sewn Edge — available on Polyethylene (PE), quoted per position and per colour.
- Hard Enamel Fill — available on Polyethylene (PE), quoted per position and per colour.
- Heat Transfer Printing — available on Polyethylene (PE), quoted per position and per colour.
- Screen Printing — available on Polyethylene (PE), quoted per position and per colour.
- Ultrasonic Welding — available on Polyethylene (PE), quoted per position and per colour.
- Anti-Rust Treatment — available on Polyethylene (PE), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed length
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with hot foil stamping applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for OEKO-TEX Standard 100 for dyes and trims are prepared for the destination market. We ship to Rotterdam or Felixstowe with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same head strength.
FAQ
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
How long does sampling take?
A first sample takes 7 working days, and each revision about 3 days.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
What is the minimum order?
Programmes start at 2000 pieces per style per finish. Mixed sizes are fine within one style.
Start your tag pin programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
