Custom Thread Trimmer — Stainless Steel with Powder Coating
We supply thread trimmer to garment factories and brands, built in Stainless Steel with powder coating for denim and workwear programmes. On a trim like this the specification that decides the outcome is tip safety, since trimming happens close to the finished garment, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 1000 pieces per style per finish.
The failures here are predictable: minimum order quantities far above what a growing brand can absorb, or unclear responsibility when a defect shows up after washing. We lock material, finish, dimension and tolerance before bulk, and prepare CPSIA and California Prop 65 compliance so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Thread Trimmer |
|---|---|
| Blade length | 25 mm |
| Type | spring-action trimmer |
| Base material | Stainless Steel |
| Finish / process | Powder Coating |
| Colour options | 8 Pantone-matched shades |
| Packing | packed to your size ratio |
| MOQ | 1000 pieces per style per finish |
| Sampling | 10 working days, 4 days per revision |
| Bulk lead time | 25-30 days after approval |
| Compliance | CPSIA and California Prop 65 compliance; EN 71 part 3 for decorative components |
| Ship to | Los Angeles or New York (North America) |
What buyers can customise
- Rose Gold Plating — available on Stainless Steel, quoted per position and per colour.
- Soft Enamel Fill — available on Stainless Steel, quoted per position and per colour.
- Mirror Polish — available on Stainless Steel, quoted per position and per colour.
- Antique Brass Plating — available on Stainless Steel, quoted per position and per colour.
- Chrome Plating — available on Stainless Steel, quoted per position and per colour.
- Sewn Edge — available on Stainless Steel, quoted per position and per colour.
- Anti-Rust Treatment — available on Stainless Steel, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed blade length
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with powder coating applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for EN 71 part 3 for decorative components are prepared for the destination market. We ship to Los Angeles or New York with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same tip safety.
FAQ
What packing options are available?
Bulk packed, carded, or packed to your own size and design ratio with barcodes applied.
What is the minimum order?
Programmes start at 1000 pieces per style per finish. Mixed sizes are fine within one style.
Do you ship to our forwarder?
Yes. We deliver to your nominated forwarder or quote landed cost under the agreed Incoterm.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
Start your thread trimmer programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
