Custom Thread Trimmer — Polycarbonate with Gunmetal Plating
We supply thread trimmer to garment factories and brands, built in Polycarbonate with gunmetal plating for e-commerce and small-batch brands. On a trim like this the specification that decides the outcome is tip safety, since trimming happens close to the finished garment, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 5000 pieces per style per finish.
The failures here are predictable: unclear responsibility when a defect shows up after washing, or a supplier who disappears once the deposit is paid. We lock material, finish, dimension and tolerance before bulk, and prepare GSO conformity with Arabic labelling so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Thread Trimmer |
|---|---|
| Blade length | 45 mm |
| Type | spring-action trimmer |
| Base material | Polycarbonate |
| Finish / process | Gunmetal Plating |
| Colour options | 24 Pantone-matched shades |
| Packing | reel packed |
| MOQ | 5000 pieces per style per finish |
| Sampling | 10 working days, 4 days per revision |
| Bulk lead time | 20-50 days after approval |
| Compliance | GSO conformity with Arabic labelling; OEKO-TEX Standard 100 for dyes and trims |
| Ship to | Jebel Ali (the Middle East) |
What buyers can customise
- Brushed Finish — available on Polycarbonate, quoted per position and per colour.
- Nickel Plating — available on Polycarbonate, quoted per position and per colour.
- Stamping — available on Polycarbonate, quoted per position and per colour.
- Injection Moulding — available on Polycarbonate, quoted per position and per colour.
- Antique Brass Plating — available on Polycarbonate, quoted per position and per colour.
- Hard Enamel Fill — available on Polycarbonate, quoted per position and per colour.
- Chrome Plating — available on Polycarbonate, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed blade length
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with gunmetal plating applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for OEKO-TEX Standard 100 for dyes and trims are prepared for the destination market. We ship to Jebel Ali with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same tip safety.
FAQ
What packing options are available?
Bulk packed, carded, or packed to your own size and design ratio with barcodes applied.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
How long does sampling take?
A first sample takes 10 working days, and each revision about 4 days.
Can you match a reference sample?
Yes. Send the trim and we match material, finish and shade, then confirm on a pre-production sample before bulk.
Start your thread trimmer programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
