Custom Button — Polyethylene (PE) with Antique Silver
We supply button to garment factories and brands, built in Polyethylene (PE) with antique silver for denim and workwear programmes. On a trim like this the specification that decides the outcome is hole burr, because a rough burr cuts thread on the line, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 1000 pieces per style per finish.
The failures here are predictable: a supplier who disappears once the deposit is paid, or colour drift between the approved sample and the bulk trim. We lock material, finish, dimension and tolerance before bulk, and prepare CPSIA and California Prop 65 compliance so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Button |
|---|---|
| Ligne | 20L / 12.5 mm |
| Attachment | 4-hole sew-through |
| Base material | Polyethylene (PE) |
| Finish / process | Antique Silver |
| Colour options | 12 Pantone-matched shades |
| Packing | carded |
| MOQ | 1000 pieces per style per finish |
| Sampling | 7 working days, 4 days per revision |
| Bulk lead time | 15-40 days after approval |
| Compliance | CPSIA and California Prop 65 compliance; OEKO-TEX Standard 100 for dyes and trims |
| Ship to | Los Angeles or New York (North America) |
What buyers can customise
- Antique Silver — available on Polyethylene (PE), quoted per position and per colour.
- Epoxy Dome — available on Polyethylene (PE), quoted per position and per colour.
- Heat Transfer Printing — available on Polyethylene (PE), quoted per position and per colour.
- Black Oxide — available on Polyethylene (PE), quoted per position and per colour.
- Laser Engraving — available on Polyethylene (PE), quoted per position and per colour.
- Debossing — available on Polyethylene (PE), quoted per position and per colour.
- Overlocked Edge — available on Polyethylene (PE), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed ligne
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with antique silver applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for OEKO-TEX Standard 100 for dyes and trims are prepared for the destination market. We ship to Los Angeles or New York with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same hole burr.
FAQ
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
How long does sampling take?
A first sample takes 7 working days, and each revision about 4 days.
What packing options are available?
Bulk packed, carded, or packed to your own size and design ratio with barcodes applied.
Can you match a reference sample?
Yes. Send the trim and we match material, finish and shade, then confirm on a pre-production sample before bulk.
Start your button programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
