Custom Button — Polypropylene (PP) with Overlocked Edge
We supply button to garment factories and brands, built in Polypropylene (PP) with overlocked edge for uniform and corporate programmes. On a trim like this the specification that decides the outcome is hole burr, because a rough burr cuts thread on the line, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 2000 pieces per style per finish.
The failures here are predictable: packing that arrives mixed and unusable on the line, or minimum order quantities far above what a growing brand can absorb. We lock material, finish, dimension and tolerance before bulk, and prepare GSO conformity with Arabic labelling so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Button |
|---|---|
| Ligne | 24L / 15 mm |
| Attachment | 2-hole sew-through |
| Base material | Polypropylene (PP) |
| Finish / process | Overlocked Edge |
| Colour options | 8 Pantone-matched shades |
| Packing | polybag per 100 |
| MOQ | 2000 pieces per style per finish |
| Sampling | 14 working days, 3 days per revision |
| Bulk lead time | 20-40 days after approval |
| Compliance | GSO conformity with Arabic labelling; salt spray test for metal finishes |
| Ship to | Jebel Ali (the Middle East) |
What buyers can customise
- Epoxy Dome — available on Polypropylene (PP), quoted per position and per colour.
- Hard Enamel Fill — available on Polypropylene (PP), quoted per position and per colour.
- Digital Printing — available on Polypropylene (PP), quoted per position and per colour.
- Offset Printing — available on Polypropylene (PP), quoted per position and per colour.
- Heat Transfer Printing — available on Polypropylene (PP), quoted per position and per colour.
- Nickel Plating — available on Polypropylene (PP), quoted per position and per colour.
- Injection Moulding — available on Polypropylene (PP), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed ligne
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with overlocked edge applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for salt spray test for metal finishes are prepared for the destination market. We ship to Jebel Ali with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same hole burr.
FAQ
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
How do you control colour on reorders?
The approved reference and the bulk standard are retained, and every reorder is checked against them before shipment.
Which compliance documents do you provide?
We prepare salt spray test for metal finishes and the supporting test reports for the destination market.
What is the minimum order?
Programmes start at 2000 pieces per style per finish. Mixed sizes are fine within one style.
Start your button programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
