Custom Tag Pin — Nickel-Free Alloy with Soft Enamel Fill
We supply tag pin to garment factories and brands, built in Nickel-Free Alloy with soft enamel fill for e-commerce and small-batch brands. On a trim like this the specification that decides the outcome is head strength, because a snapped head leaves the pin in the garment, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 2000 pieces per style per finish.
The failures here are predictable: shade variation within one carton, or unclear responsibility when a defect shows up after washing. We lock material, finish, dimension and tolerance before bulk, and prepare UKCA and REACH documentation so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Tag Pin |
|---|---|
| Length | 50 mm |
| Type | barbless pin |
| Base material | Nickel-Free Alloy |
| Finish / process | Soft Enamel Fill |
| Colour options | 16 Pantone-matched shades |
| Packing | polybag per 100 |
| MOQ | 2000 pieces per style per finish |
| Sampling | 7 working days, 3 days per revision |
| Bulk lead time | 15-40 days after approval |
| Compliance | UKCA and REACH documentation; GRS recycled content claim |
| Ship to | Felixstowe (the United Kingdom) |
What buyers can customise
- Debossing — available on Nickel-Free Alloy, quoted per position and per colour.
- Digital Printing — available on Nickel-Free Alloy, quoted per position and per colour.
- Soft Enamel Fill — available on Nickel-Free Alloy, quoted per position and per colour.
- Injection Moulding — available on Nickel-Free Alloy, quoted per position and per colour.
- Epoxy Dome — available on Nickel-Free Alloy, quoted per position and per colour.
- Sewn Edge — available on Nickel-Free Alloy, quoted per position and per colour.
- Rubber Coating — available on Nickel-Free Alloy, quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed length
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with soft enamel fill applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for GRS recycled content claim are prepared for the destination market. We ship to Felixstowe with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same head strength.
FAQ
Can you do small runs across many designs?
Yes — many studio and boutique programmes run small quantities across a wide design set.
What is the minimum order?
Programmes start at 2000 pieces per style per finish. Mixed sizes are fine within one style.
Which compliance documents do you provide?
We prepare GRS recycled content claim and the supporting test reports for the destination market.
How long does sampling take?
A first sample takes 7 working days, and each revision about 3 days.
Start your tag pin programme
Send us a reference sample, a drawing or a spec sheet and we will come back with material options, a costing and a sampling timetable.
