Custom Thread Trimmer — Nylon (PA) with Epoxy Dome
We supply thread trimmer to garment factories and brands, built in Nylon (PA) with epoxy dome for childrenswear and schoolwear. On a trim like this the specification that decides the outcome is spring tension, which decides fatigue over a long run, so that is agreed in writing before bulk — not discovered when the first carton is opened on the line. Programmes start at 500 pieces per style per finish.
The failures here are predictable: a finish that tarnishes or rubs off after washing, or minimum order quantities far above what a growing brand can absorb. We lock material, finish, dimension and tolerance before bulk, and prepare SNI or SIRIM documentation per destination so the shipment clears instead of sitting at port while your selling season passes.
Specification
| Product | Thread Trimmer |
|---|---|
| Blade length | 60 mm |
| Type | thread snip |
| Base material | Nylon (PA) |
| Finish / process | Epoxy Dome |
| Colour options | 12 Pantone-matched shades |
| Packing | reel packed |
| MOQ | 500 pieces per style per finish |
| Sampling | 12 working days, 4 days per revision |
| Bulk lead time | 15-50 days after approval |
| Compliance | SNI or SIRIM documentation per destination; OEKO-TEX Standard 100 for dyes and trims |
| Ship to | Jakarta or Port Klang (Asia-Pacific) |
What buyers can customise
- Powder Coating — available on Nylon (PA), quoted per position and per colour.
- Nickel Plating — available on Nylon (PA), quoted per position and per colour.
- Chrome Plating — available on Nylon (PA), quoted per position and per colour.
- Rubber Coating — available on Nylon (PA), quoted per position and per colour.
- Soft Enamel Fill — available on Nylon (PA), quoted per position and per colour.
- Anti-Rust Treatment — available on Nylon (PA), quoted per position and per colour.
- Stamping — available on Nylon (PA), quoted per position and per colour.
How we produce it
- Drawing or reference sample review, with size and finish confirmed
- Material selection and a finish sample or strike-off
- Prototype made to the agreed blade length
- Fit and wash test on the actual garment fabric, then a pre-production sample
- Bulk run with epoxy dome applied under controlled settings
- In-line inspection, final AQL 2.5 inspection and packing to your ratio
Where it is used
- Denim and workwear — hard-wearing finishes that survive industrial washing
- Outerwear and tailoring — matched to the shell fabric so it drapes with the garment
- Childrenswear and schoolwear — tested to the destination's safety standard
- Bridal and eveningwear — small runs with hand-finished detail
- Uniform and corporate programmes — repeatable spec held on file for reorders
Packing, testing and delivery
Trims are packed to the ratio you specify — by size, by colour or by garment set — with barcodes applied where the line needs them. Test reports for OEKO-TEX Standard 100 for dyes and trims are prepared for the destination market. We ship to Jakarta or Port Klang with the commercial invoice, packing list and certificate of origin, and hold the approved reference so reorders reproduce the same material, the same finish and the same spring tension.
FAQ
What is the minimum order?
Programmes start at 500 pieces per style per finish. Mixed sizes are fine within one style.
How long does sampling take?
A first sample takes 12 working days, and each revision about 4 days.
Which compliance documents do you provide?
We prepare OEKO-TEX Standard 100 for dyes and trims and the supporting test reports for the destination market.
What packing options are available?
Bulk packed, carded, or packed to your own size and design ratio with barcodes applied.
Start your thread trimmer programme
If you already have a supplier, send us the last problem you had with them. That is usually where we start.
